Forum: General Motorcycles only  18-Jul-2004, 20:41 |
| Replies: 18 Views: 3,516 You definetly don't need the stamps for the 888...
You definetly don't need the stamps for the 888 as it's not even seen a tank of fuel since you've had it. I bet you have to get your mates to put it back together for you. Jeeze if your not loosing... |
| Forum: 998 / 996 / 916 / 748 09-Jul-2004, 01:20 |
| Replies: 36 Views: 3,047 Caliper should fit straight on. I had a problem...
Caliper should fit straight on. I had a problem with what appeared to be mine flexing and a mate had a spare. It look to be just a slighlty newer design but does use different pads. Not sure it is... |
| Forum: 998 / 996 / 916 / 748 02-Jul-2004, 19:13 |
| Replies: 36 Views: 3,047 I'm an avid rear brake fan, got mile r caliper,...
I'm an avid rear brake fan, got mile r caliper, wavy disk and a nicely greased pivot shaft, oo err. Really and utterly great for shrugging off that last bit off excess speed or tightening the line... |
| Forum: General Motorcycles only 23-Jun-2004, 23:27 |
| Replies: 9 Views: 2,541 Got EBC HH pads on my SPS cast iron floating...
Got EBC HH pads on my SPS cast iron floating disks.
They have been on there with EBC pads for just over 7k miles now after replacing the supplied carbon lorraine pads (after 5K)as they were not a... |
| Forum: 998 / 996 / 916 / 748 11-Jun-2004, 00:20 |
| Replies: 7 Views: 1,732 Mine did that years back. Turned out to be a...
Mine did that years back. Turned out to be a crack in the bottom yoke, Uner hard breaking it opened up andallowed the for to actually move in the yoke. Check around the clamp bolts real carefully.... |
| Forum: 998 / 996 / 916 / 748 10-Jun-2004, 23:39 |
| Replies: 30 Views: 5,193 |
| Forum: 998 / 996 / 916 / 748 08-Jun-2004, 19:24 |
| Replies: 30 Views: 5,193 |
| Forum: 998 / 996 / 916 / 748 06-Jun-2004, 23:33 |
| Replies: 4 Views: 1,335 Cheers Neil, Got it all apart within abiut five...
Cheers Neil,
Got it all apart within abiut five minutes as per yours and Andy's instructions. Will give D.UK a ring tomorrow. Thanks to you both for the adbvice. If you ever fancy some cool roads in... |
| Forum: 998 / 996 / 916 / 748 06-Jun-2004, 12:11 |
| Replies: 4 Views: 1,335 |
| Forum: General Motorcycles only 06-Jun-2004, 12:06 |
| Replies: 8 Views: 6,066 By taking them apart do you mean removing the...
By taking them apart do you mean removing the actual lens. If so you will have to replace the lens using silicon or a similar sealing compound, this will outgas and could cause the misting.... |
| Forum: 998 / 996 / 916 / 748 06-Jun-2004, 11:45 |
| Replies: 4 Views: 1,335 MOT time, light beam corrector
MOT time again, where they stick loads of bits of tape over my lights to try and make them point the right way. These must be an import set. I believe there is a way to get the beam corrected with a... |
| Forum: 998 / 996 / 916 / 748 07-Feb-2004, 19:26 |
| Replies: 16 Views: 2,338 Hi Steveg, Had the same problem with a badly...
Hi Steveg,
Had the same problem with a badly adjusted lever a long while back. If they replaced cylinder but not the lever the problem would get transfered. Would be very suprised to find any brake... |
| Forum: 998 / 996 / 916 / 748 31-Jul-2003, 18:54 |
| Replies: 5 Views: 1,714 Mines cut back to leave about the same....
Mines cut back to leave about the same. You've got to remove the screens as they are by far the most restrictive part. The surface area of the screen must be in order of +40%. If you remove one... |
| Forum: 998 / 996 / 916 / 748 07-Jun-2003, 10:15 |
| Replies: 6 Views: 2,518 998 Addict. Could you post your dyno charts as...
998 Addict. Could you post your dyno charts as that would be really interesting. I was also told that 45mm is the best set-up on a 916BP(Probably different on 996 and SP variants). I think the moto... |
| Forum: 998 / 996 / 916 / 748 26-May-2003, 18:05 |
| Replies: 35 Views: 7,498 |
| Forum: 998 / 996 / 916 / 748 26-May-2003, 17:58 |
| Replies: 20 Views: 26,895 If you push the metal clips in on the tank side...
If you push the metal clips in on the tank side fuel does not come out. They purely retain the male fitting once pushed in to place. It is best to push these in as you fit the connector as it moves... |
| Forum: 998 / 996 / 916 / 748 23-May-2003, 23:44 |
| Replies: 20 Views: 26,895 |
| Forum: 998 / 996 / 916 / 748 23-May-2003, 21:28 |
| Replies: 35 Views: 7,498 |
