Ducati Sporting Club UK
 
 
Thread Tools Search this Thread Display Modes
  #1  
Old 28-Sep-2003, 21:24
Lee1980's Avatar
Lee1980 Lee1980 is offline
Registered Forum User
Big Twin
Bikes: Xdaivel
 
Posts: 1,051
Join Date: Aug 2003
Mood: Xdiavel..awesome!!
Radiator damage

Only had my 748s two days 90 miles on the clock and got two dents in the fins on the rad from stones.

Is there a guard avaliable, does it work well and not stop the air flow?

A bit late now, will try and bend the fins striaght.

Why ain't there one as standard?

Thanks

Lee1980
Quote+Reply
  #2  
Old 28-Sep-2003, 21:41
Nigel C's Avatar
Nigel C Nigel C is offline
Registered Forum User
Big Twin
 
Posts: 1,710
Join Date: Aug 2002
Mood: happy bike passed MOT
I think there is something you can do, a couple of the guys on here have done something i think but can't remember who

you can bend the fins back but you have to be careful

[Edited on 28-9-2003 by Nigel C]
Quote+Reply
  #3  
Old 28-Sep-2003, 22:14
Old Yella Old Yella is offline
Registered Forum User
Big Twin
Bikes: Kawasaki ZX10r D6f, Dawes XC2.4, Planet X Superlight Pro Carbon
 
Posts: 1,428
Join Date: Jul 2002
Mood: aving a laff
B+Q

B+Q sell some nice gold mesh for covering vent grilles.
Cut it to shape and tie in with wire loops in corners and you have a good looking stone protector that does not stop air flow but takes the hits before the rad gets punctured.
Have some pics at work and will post tomoz
Quote+Reply
  #4  
Old 28-Sep-2003, 23:50
Totto Totto is offline
Registered Forum User
Big Twin
 
Posts: 1,262
Join Date: Jul 2002
Mood: Not so broke any more !!!!!!!!
Yep B&Q , but you can get the mesh in silver for THE RED Ducati's , gold only looks OK on the other colour :P
Quote+Reply
  #5  
Old 28-Sep-2003, 23:53
antonye's Avatar
DSC Member antonye antonye is offline
Administrator
Webteam
MotoGP God
Bikes: 748S, HM1100S, V4SP, Was: DD-A #111
 
Posts: 13,053
Join Date: Feb 2002
Mood: Passion Killer
As Old Yella says, B&Q do a wide range of different sized mesh in different colours (plain stainless would be best for yours rather than gold though!) which you can buy in various size sheets.

A radiator sized sheet (about the same size as an A4 piece of paper) is about a fiver - I bought one to make up a mesh for a carbon v-piece.

You only need to make a slight curve in it to follow the line of the radiator. You can then bend the edges around (use a thick pair of gloves to save your fingers) to hold it all in place. Wind pressure will stop it falling off and hold it in place anyway.

As long as you make sure you keep the wheel/mudguard clearance it will be fine.

Don't worry about the odd stonechip though. We all get them and it will take a major dent in the rad to make any difference in efficiency.
Quote+Reply
  #6  
Old 29-Sep-2003, 15:22
Shazaam!'s Avatar
DSC Member Shazaam! Shazaam! is offline
DSC Club Member
Big Twin
 
Posts: 1,167
Join Date: Nov 2001
This is an easy do-it-yourself project for a superbike. First straighten any bent radiator fins. Then cut a piece of aluminum window screening to fit leaving 4-5 inches on top to make some tabs to bend over the top and back of the radiator. It conforms easily to the curved radiator shape and the wind pressure holds it firmly against the radiator.

Remove the V-shaped lower cowl and attach another piece of screen to protect the oil cooler. Fasten it to the back of the panel with small self-tapping screws and washers at the four molded holes.*Silicone adhesive or double-sided tape also works.

Any screening will reduce airflow somewhat, of course. The smaller the mesh, the more protection against smaller debris. I can only offer that common aluminum window screen works fine in desert temperatures with no noticeable effect on 916 coolant temperatures.

I wish I thought of it right away before fin damage occurred. After 20,000 miles, I still haven't had to replace it. I used window screening simply because it's cheap to replace and has a fine-enough mesh to spread out the impact load (and keep bugs out), but if you prefer something different, check out the McMaster-Carr web site. When they sell mesh screening, they define the percent open area that tells you its ability to flow air.
Quote+Reply
  #7  
Old 29-Sep-2003, 17:07
Old Yella Old Yella is offline
Registered Forum User
Big Twin
Bikes: Kawasaki ZX10r D6f, Dawes XC2.4, Planet X Superlight Pro Carbon
 
Posts: 1,428
Join Date: Jul 2002
Mood: aving a laff
Looks like this when fitted

Pic 1
Quote+Reply
  #8  
Old 29-Sep-2003, 17:10
Old Yella Old Yella is offline
Registered Forum User
Big Twin
Bikes: Kawasaki ZX10r D6f, Dawes XC2.4, Planet X Superlight Pro Carbon
 
Posts: 1,428
Join Date: Jul 2002
Mood: aving a laff
And this

Seat unit vents
Quote+Reply
  #9  
Old 29-Sep-2003, 21:07
Lee1980's Avatar
Lee1980 Lee1980 is offline
Registered Forum User
Big Twin
Bikes: Xdaivel
 
Posts: 1,051
Join Date: Aug 2003
Mood: Xdiavel..awesome!!
Thanks guys

Thanks for the replies guys, and the pics Old yella.

I'll get down to Do-it all when I can and see what they got.

Thanks

Lee1980
Quote+Reply
  #10  
Old 30-Sep-2003, 10:39
Old Yella Old Yella is offline
Registered Forum User
Big Twin
Bikes: Kawasaki ZX10r D6f, Dawes XC2.4, Planet X Superlight Pro Carbon
 
Posts: 1,428
Join Date: Jul 2002
Mood: aving a laff
Cheers mate but B&Q are the only place I could find the stuff.
Tried loads of others but no joy.
Hope you get some mate, happy hunting.
Quote+Reply
Reply
  
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes
Postbit Selector
Switch to Vertical postbit Use Vertical Postbit

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Recent Posts - Contact Us - DSC Home - Archive - Top
Powered by vBulletin 3.5.4 - Copyright © 2000 - 2024, Jelsoft Enterprises Ltd. - © Ducati Sporting Club UK - All times are GMT +1. The time now is 13:28.