Ducati Sporting Club UK

Ducati Sporting Club UK (/msgboard.php)
-   998 / 996 / 916 / 748 (/forumdisplay.php?f=85)
-   -   998 fan problem ????? (/showthread.php?t=365976)

dunlop0_1 27-Oct-2014 19:13

998 fan problem ?????
 
Ok I managed to get hold of a 998 fan. Ran a test with it tonight but found the following issues.

Turn ignition on fan runs for approx 1 second (weird)
Run bike up to and past temp and nothing happens until I disconnect the temp sensor plug and then the fan runs but won't switch off even when cool.

I know the fan is controlled by the ecu but I was wondering if having a none 998 ecu remapped for the 998 would affect the fan circuit?

Think I might just hard wire it with the old 996 fan switch in place LOL

skidlids 27-Oct-2014 19:24

Only one fan Neil, my 998s have two fans and they come on at different points from what I recall, haven't run them properly for a while now, try plugging it into the other fan connector

dunlop0_1 27-Oct-2014 19:46

Will do Kev. I had read about the fans operating at two different temps. :)

antonye 27-Oct-2014 23:00

I'll check what temp the fans come on for you - and it shouldn't make any difference with your ECUs as they're reflashed rather than remapped, so identical to off-the-shelf Ducati ECUs ;)

dunlop0_1 28-Oct-2014 06:14

Thanks Ant

antonye 29-Oct-2014 09:42

I've checked all the software revisions and they all say that Fan 1 is 101 and Fan 2 is 102.
I know that sounds like not very much difference between the two, which is why I checked all versions I have (about 6) but that's what they all say!

dunlop0_1 29-Oct-2014 10:05

Quote:

Originally Posted by antonye
I've checked all the software revisions and they all say that Fan 1 is 101 and Fan 2 is 102.
I know that sounds like not very much difference between the two, which is why I checked all versions I have (about 6) but that's what they all say!



Thanks again matey

dunlop0_1 01-Nov-2014 15:24

Tried the other side Kev and the fan is just on all the time as if it's hot or something. It's now hard wired through the old 996 fan switch and works fine. Still would like to find the issue though. :confused:

skidlids 01-Nov-2014 16:17

Neil, I take it you did change the 996 thermal switch in the water system for the thermal sensor (thermistor)used on the 998s

dunlop0_1 01-Nov-2014 20:40

Yes I did my learned friend. :)

skidlids 01-Nov-2014 21:07

Quote:

Originally Posted by dunlop0_1
Yes I did my learned friend. :)


Beats me then, as the ECU reads the thermistor and then switches the fans at the pre programmed settings, with the Fans are always Live with the Earth switched by the ECU

Spjallen 03-Nov-2014 20:50

Could it be a faulty thermistor then?

dunlop0_1 04-Nov-2014 19:55

Quote:

Originally Posted by Spjallen
Could it be a faulty thermistor then?


could be as there nowt to say the 998 one I have is working correctly. No spare so it will have to stay as it is for now.

skidlids 04-Nov-2014 21:28

Pretty much the same as the one in the front cylinder rocker cover of a class A bike, think its a WTS09 or something like that


All times are GMT +1. The time now is 08:56.

Powered by vBulletin 3.5.4 - Copyright © 2000 - 2025, Jelsoft Enterprises Ltd.
© Ducati Sporting Club UK