Rearsets

dave996 · 14-Jan-2006, 23:06

I have recently bought some rearsets without any fitting instructions.
Could someone take a pic of the left side (gear change) please. The only reason I'm confused is that it came with a load of spare levers (race I imagine).
The rearsets were bought from tecmoto and are in the syle of DP ones.

Cheers
d

Carbon749 · 14-Jan-2006, 23:10

Hi, do they have the race shift or road shift ??? I have a good pic of road shift DP ones .... any good?

Karl · 15-Jan-2006, 00:20

Dave
Hope this helps?

TopiToo · 15-Jan-2006, 00:31

Hello

Just out of intrest, I have fitted some Harris rear sets, and finding it a little difficult to set them right for my riding position, more so gear changing.
Due to the fact they are adjustable, is there a basic/general rule of thumb,
or is it a case of adjust/test etc.

Sorry maybe answered my own question. . .

regards

TopiToo

dave996 · 15-Jan-2006, 01:05

Cheers Karl, I don't have a bit that the gear lever attaches to.

Carbon749, I think I have both but I after the road set up.

Cheers

d

Karl · 15-Jan-2006, 02:04

Dave if it's the part I think you're refering to (the bush) then that normally doesn't come with the set, you just use the one off your stock rearsets

Carbon749 · 15-Jan-2006, 10:24

Quote:

Originally posted by dave996
Cheers Karl, I don't have a bit that the gear lever attaches to.

Carbon749, I think I have both but I after the road set up.

Cheers

d

Don't think you mean the bush in the gear lever I think you mean the shaft / pin. If so, again you used your standard one. The linkage between the gear lever and the splined shaft can be your standard linkage.

If you mean that you do not have the bolt hole below the foot peg to screw the shaft / pivot bolt in to then you have run with a race shift, ie: gear lever straight on to the splined gear shaft.

dave996 · 15-Jan-2006, 14:30

Right, this is what I have, I also have a black rod for the gear change linkage.

What seems to be missing is a way of attaching the gear change, the thing is I've looked in my Ducati calaloge and everything is the same!

Any more advice!

andyb · 15-Jan-2006, 15:41

Where are the foot pegs? Those levers do they rotate on a part of the peg, prior to it fittng in the clamp hole in the mounting?

skidlids · 15-Jan-2006, 15:47

Dave I sold some to Dallas a short while back woth the gear lever pivot point, but as he uses race gear pattern you could probably swap the bit with him.
I will also have a buyer for those extended gearshifts on the left of the pic if you want to part with them and it could mean another of the shorter gear levers coming your way

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode
Postbit Selector
Use Horizontal Postbit

14-Jan-2006, 23:10	#2
Carbon749 Registered Forum User Big Twin Posts: 1,956 Join Date: Mar 2005 Location: Normally in my own little world Mood: I own a flame thrower Hi, do they have the race shift or road shift ??? I have a good pic of road shift DP ones .... any good? Reply

15-Jan-2006, 00:20	#3
Karl DSC Club Member 500SD Posts: 667 Join Date: May 2001 Location: Oxfordshire Dave Hope this helps? Reply

15-Jan-2006, 01:05	#5
dave996 Registered Forum User 888 at Last !!! Posts: 952 Join Date: Dec 2004 Location: Carterton Mood: Fed up... Cheers Karl, I don't have a bit that the gear lever attaches to. Carbon749, I think I have both but I after the road set up. Cheers d Reply

15-Jan-2006, 02:04	#6
Karl DSC Club Member 500SD Posts: 667 Join Date: May 2001 Location: Oxfordshire Dave if it's the part I think you're refering to (the bush) then that normally doesn't come with the set, you just use the one off your stock rearsets Reply

15-Jan-2006, 14:30	#8
dave996 Registered Forum User 888 at Last !!! Posts: 952 Join Date: Dec 2004 Location: Carterton Mood: Fed up... rearsets Right, this is what I have, I also have a black rod for the gear change linkage. What seems to be missing is a way of attaching the gear change, the thing is I've looked in my Ducati calaloge and everything is the same! Any more advice! Reply

15-Jan-2006, 15:41	#9
andyb Registered Forum User BSB Star Posts: 6,720 Join Date: Feb 2002 Location: northampton Mood: Has change happened...must of missed it! Where are the foot pegs? Those levers do they rotate on a part of the peg, prior to it fittng in the clamp hole in the mounting? Reply