Ducati Sporting Club UK
Page 2 of 3 < 1 2 3 >
Showing results 51 to 100 of 115
Search took 0.00 seconds; generated 80 minute(s) ago. Search: Posts Made By: Nigel Booker
Forum: 998 / 996 / 916 / 748 13-Oct-2003, 23:01
Replies: 3
Views: 1,589
Posted By Nigel Booker
Try a set of JHP alloy plates, about £140 a set...

Try a set of JHP alloy plates, about £140 a set but well worth the money.
Forum: 998 / 996 / 916 / 748 11-Oct-2003, 01:11
Replies: 11
Views: 2,199
Posted By Nigel Booker
Looks like I may have to speak to the dealer that...

Looks like I may have to speak to the dealer that installed my alarm as well.

Thanks for the info Lee.
Forum: 998 / 996 / 916 / 748 08-Oct-2003, 23:14
Replies: 11
Views: 2,199
Posted By Nigel Booker
Lee let me know how you get on as the datatool...

Lee let me know how you get on as the datatool alarm on my 996 is fitted under the seat. I've never seen any micro switch, but the alarm does go off if you as much as sneeze near the bike.

BTW...
Forum: 998 / 996 / 916 / 748 08-Oct-2003, 20:58
Replies: 11
Views: 2,199
Posted By Nigel Booker
Would it make any difference if the alarm went...

Would it make any difference if the alarm went off, nobody takes any notice of them. The organised light fingered b&£$%*ds are usually so quick that you dont get much chance to do anything about it?
Forum: 998 / 996 / 916 / 748 03-Oct-2003, 07:00
Replies: 16
Views: 3,078
Posted By Nigel Booker
I had only the two bolts holding a dp hugger on...

I had only the two bolts holding a dp hugger on my 748. When the top bolt came out it moved so much that it ended up touching the underside of the exhaust and burnt an 1" x 2" hole in the hugger.
Forum: 998 / 996 / 916 / 748 03-Oct-2003, 06:44
Replies: 4
Views: 2,469
Posted By Nigel Booker
I have the STM version from Tecmoto and its...

I have the STM version from Tecmoto and its definitely worth the money. Looks good and no leaks.
Forum: 998 / 996 / 916 / 748 30-Sep-2003, 00:14
Replies: 17
Views: 3,485
Posted By Nigel Booker
Guido, did you get the slave cylinder from a...

Guido,
did you get the slave cylinder from a stockist in the uk or direct from evoluzione?
Forum: 998 / 996 / 916 / 748 27-Sep-2003, 21:15
Replies: 17
Views: 3,485
Posted By Nigel Booker
Jasper, so which type of master cylinder will...

Jasper,
so which type of master cylinder will make the most difference? Would the Brembo or AP billet master cylinders be any good?
Forum: 998 / 996 / 916 / 748 27-Sep-2003, 20:49
Replies: 17
Views: 3,485
Posted By Nigel Booker
Jasper, how much difference does it make, can you...

Jasper,
how much difference does it make, can you operate the clutch with the same amount of pressure as a cable operated clutch?

I need to get a decent reduction in the pressure required as since...
Forum: 998 / 996 / 916 / 748 27-Sep-2003, 20:43
Replies: 17
Views: 3,485
Posted By Nigel Booker
Sorry jasper not to clear on that last post. I...

Sorry jasper not to clear on that last post.

I meant are you using the dedicated tecmoto version or the stm model sold by tecmoto?
Forum: 998 / 996 / 916 / 748 27-Sep-2003, 20:38
Replies: 17
Views: 3,485
Posted By Nigel Booker
Jasper are you using the newer style stm slave...

Jasper are you using the newer style stm slave cylinder?

Tecmoto sell one for £150 did you buy it from them?
Forum: 998 / 996 / 916 / 748 27-Sep-2003, 20:08
Replies: 17
Views: 3,485
Posted By Nigel Booker
Anybody using an oversize clutch slave cylinder?

I've been looking at the alternative clutch slave cylinders on offer has anybody got any thoughts on which is the best quality, price and reduction in clutch pressure.

The only options...
Forum: 998 / 996 / 916 / 748 23-Sep-2003, 00:45
Replies: 5
Views: 1,704
Posted By Nigel Booker
Lee, it may sound obvious but give some thought...

Lee, it may sound obvious but give some thought to which bits you may change for after market items. I put the etch markings on the front fender, v piece and dual seat unit and then replaced the lot...
Forum: 998 / 996 / 916 / 748 23-Sep-2003, 00:12
Replies: 5
Views: 1,704
Posted By Nigel Booker
Fitted both the kits on my 748 and 996. Found it...

Fitted both the kits on my 748 and 996. Found it wasn't a major job if you remove the parts that your putting the etching marks on and just take your time. Have a look at a few dukes in your...
Forum: 998 / 996 / 916 / 748 12-Sep-2003, 19:56
Replies: 13
Views: 3,531
Posted By Nigel Booker
My 996 bip did it until I fitted an ultimap chip.

My 996 bip did it until I fitted an ultimap chip.
Forum: 998 / 996 / 916 / 748 10-Sep-2003, 00:41
Replies: 9
Views: 1,857
Posted By Nigel Booker
As nelly says the dp stuff fits well, but can be...

As nelly says the dp stuff fits well, but can be flimsy and pricey. I have a dp hugger fitted and find the that its of a good quality, its been on the bike for 11K now and still looks as good as...
Forum: 998 / 996 / 916 / 748 07-Sep-2003, 22:32
Replies: 8
Views: 2,247
Posted By Nigel Booker
Take a look at the state of the mesh and you can...

Take a look at the state of the mesh and you can see why the bike breathes and sounds better.

Even on a new bike the mesh is so fine that it restricts the amount of air that gets into the box.
Forum: Shazaam! on Chassis and Suspension 06-Sep-2003, 18:42
Replies: 20
Views: 10,807
Posted By Nigel Booker
I'll still be sticking with the dunlops!

I'll still be sticking with the dunlops!
Forum: Tyres 06-Sep-2003, 18:42
Replies: 20
Views: 7,442
Posted By Nigel Booker
I'll still be sticking with the dunlops!

I'll still be sticking with the dunlops!
Forum: 998 / 996 / 916 / 748 29-Aug-2003, 00:34
Replies: 36
Views: 8,139
Posted By Nigel Booker
Totally agree with the others walk away and tell...

Totally agree with the others walk away and tell the dealer what you expect to pay for the deal and that you are talking to other ducati dealers. Even show him the prices from other dealers and trade...
Forum: 998 / 996 / 916 / 748 27-Aug-2003, 21:37
Replies: 25
Views: 4,550
Posted By Nigel Booker
As far as I was told they are just fitted for...

As far as I was told they are just fitted for noise reduction, but the engine seems to respond better without them and the induction noise is great.
Forum: 998 / 996 / 916 / 748 26-Aug-2003, 22:23
Replies: 3
Views: 1,552
Posted By Nigel Booker
Sounds a bit overpriced to me. CMW in chichester...

Sounds a bit overpriced to me. CMW in chichester have a low mileage 97 916BP for sale at £4999 c/w 50mm termi's and alarm. As a rule i find CMW prices are at the top end for ducatis. Usually...
Forum: 998 / 996 / 916 / 748 23-Aug-2003, 10:07
Replies: 5
Views: 1,769
Posted By Nigel Booker
Read somewhere that its not really worth spending...

Read somewhere that its not really worth spending a lot of time and money on blue printing and gas flowing the heads on ducatis as the factory produced item is of such a high quality.

Not my opinion...
Forum: 998 / 996 / 916 / 748 19-Aug-2003, 19:46
Replies: 7
Views: 2,593
Posted By Nigel Booker
Used the skidmarx corse screen for about 2 years...

Used the skidmarx corse screen for about 2 years now. Its not to everybodys liking as it does sit very high but gives excellent wind protection. From memory I think the screen is about £35 so its...
Forum: 998 / 996 / 916 / 748 19-Aug-2003, 19:42
Replies: 19
Views: 3,899
Posted By Nigel Booker
How many miles have the plates done? I generally...

How many miles have the plates done? I generally find that the plates start to slip after about 8-9k, but still last for another 2k with a bit of care on take up.
Forum: 998 / 996 / 916 / 748 17-Aug-2003, 00:28
Replies: 6
Views: 2,749
Posted By Nigel Booker
Same here 180 section every time, never liked the...

Same here 180 section every time, never liked the fashion statement 190 section tyre.
Forum: 998 / 996 / 916 / 748 13-Aug-2003, 20:37
Replies: 9
Views: 2,719
Posted By Nigel Booker
Dave, I tried to get seal kits for the master...

Dave,
I tried to get seal kits for the master cylinder and caliper but had no luck. If either is faulty I would ring around a few breakers and see whats available. I got an almost new rear caliper...
Forum: 998 / 996 / 916 / 748 09-Aug-2003, 23:50
Replies: 9
Views: 2,719
Posted By Nigel Booker
Dave, if you have adjusted the rear brake lever...

Dave,
if you have adjusted the rear brake lever it would pay you to slacken it back off asap. If you attempt to get a better rear brake by adjusting the amount of travel in the pin and clevis on the...
Forum: 998 / 996 / 916 / 748 07-Aug-2003, 06:57
Replies: 9
Views: 2,719
Posted By Nigel Booker
Dave, I would get it looked at asap my 748 had a...

Dave,
I would get it looked at asap my 748 had a similar brake problem and eventually I had the rear caliper and brake line melt. Turned out that the master cyclinder was not returning correctly and...
Forum: 998 / 996 / 916 / 748 06-Aug-2003, 20:35
Replies: 0
Views: 1,373
Posted By Nigel Booker
Any dealings with PUAAR motosport?

My 996 has been collected by PUAAR motosport of barking for an estimate on accident repairs. RSS recommended them to me and apparently they do paint and panel repair work for FP, HM plant and Virgin...
Forum: 998 / 996 / 916 / 748 06-Aug-2003, 20:27
Replies: 12
Views: 3,512
Posted By Nigel Booker
I've had a set for about six months now, I...

I've had a set for about six months now, I only got them for track days but decided to give them a bit of run to check the effect on the performance. I ran the bike with the baffles in for about...
Forum: 998 / 996 / 916 / 748 05-Aug-2003, 00:38
Replies: 9
Views: 2,117
Posted By Nigel Booker
Nice idea jon when I get the bike sorted...

Nice idea jon when I get the bike sorted I'll have to go for ride and get some pics taken.
Forum: 998 / 996 / 916 / 748 03-Aug-2003, 00:19
Replies: 3
Views: 2,171
Posted By Nigel Booker
126 at the crank and 116 at the rear wheel on a...

126 at the crank and 116 at the rear wheel on a 996bip with 50mm termis and ducati performance eprom. Never run it on the dyno with the FIM ultimap chip thats now fitted.
Forum: 998 / 996 / 916 / 748 02-Aug-2003, 10:37
Replies: 15
Views: 3,928
Posted By Nigel Booker
mounted on the subframe bolt next to the rear...

mounted on the subframe bolt next to the rear shock.
Forum: 998 / 996 / 916 / 748 01-Aug-2003, 22:36
Replies: 20
Views: 3,661
Posted By Nigel Booker
Thrustercat, I know exactly what you mean took me...

Thrustercat,
I know exactly what you mean took me a few months to get the hang of finding neutral on my first ducati. But after adjusting the gear change mechanism to suit me and a lot of practice...
Forum: 998 / 996 / 916 / 748 31-Jul-2003, 20:41
Replies: 20
Views: 3,661
Posted By Nigel Booker
Agree with totto always found neutral by keeping...

Agree with totto always found neutral by keeping the bike moving. That said if the clutch plates are getting worn then it can still be a pain to find neutral.
Forum: 998 / 996 / 916 / 748 29-Jul-2003, 22:59
Replies: 2
Views: 1,711
Posted By Nigel Booker
I think its listed as the rear sprocket coupling...

I think its listed as the rear sprocket coupling nut with a torque setting of 156nm. The rear wheel nut is 176nm.
Forum: 998 / 996 / 916 / 748 28-Jul-2003, 20:29
Replies: 5
Views: 1,956
Posted By Nigel Booker
Had my 996 misfire back through the airbox....

Had my 996 misfire back through the airbox. Thought the fuel tank had exploded and so did most people at the service station. Only ever had it happen the once.
Forum: 998 / 996 / 916 / 748 21-Jul-2003, 22:53
Replies: 9
Views: 2,117
Posted By Nigel Booker
Which rearsets?

Anybody got an opinion on which rearsets are the best for adjustment, price and quality? I'm in the market for a set after destroying another set of boots, I can't get out of the habit of...
Forum: 998 / 996 / 916 / 748 20-Jul-2003, 23:47
Replies: 24
Views: 7,531
Posted By Nigel Booker
Tried PJ1 blue and chain kote teflon spray but...

Tried PJ1 blue and chain kote teflon spray but eventually settled on castrol chain wax. Makes less of a mess and seems to stay on the chain longer than most. Covered about 12k on the original chain...
Forum: 998 / 996 / 916 / 748 19-Jul-2003, 09:26
Replies: 9
Views: 2,687
Posted By Nigel Booker
Order one from malplates.co.uk thanks for the...

Order one from malplates.co.uk

thanks for the help
Forum: 998 / 996 / 916 / 748 18-Jul-2003, 20:55
Replies: 13
Views: 4,144
Posted By Nigel Booker
Forgot to mention that my local ducati dealer...

Forgot to mention that my local ducati dealer didn't fix the problem an RAC mechanic that took part in the pro thunder series said its a common fault.
Forum: 998 / 996 / 916 / 748 18-Jul-2003, 20:53
Replies: 13
Views: 4,144
Posted By Nigel Booker
Have you checked the starter relay connections...

Have you checked the starter relay connections had the leads disconnect themselves twice in 12 months.
Forum: 998 / 996 / 916 / 748 18-Jul-2003, 20:42
Replies: 9
Views: 2,687
Posted By Nigel Booker
May have to get one from the ads in MCN next week...

May have to get one from the ads in MCN next week but I still need to get one for this weekend.

thanks anyway
Forum: 998 / 996 / 916 / 748 18-Jul-2003, 20:03
Replies: 9
Views: 2,687
Posted By Nigel Booker
Kevin, my only solution so far is to cut the...

Kevin,
my only solution so far is to cut the legal plate down. At least it will still have legal lettering sizes and I can reduce it to 7.5x7 so it should fit. Just been told I can get one made at...
Forum: 998 / 996 / 916 / 748 18-Jul-2003, 19:09
Replies: 9
Views: 2,687
Posted By Nigel Booker
Need a 7x7 number plate PDQ

Anybody know where I can get a replacement number plate, preferably a while you wait supplier in sussex. I just fitted a evoluzione licence relocator and now need a 7x7 plate.

many thanks nigel
Forum: 998 / 996 / 916 / 748 12-Jul-2003, 13:13
Replies: 17
Views: 5,526
Posted By Nigel Booker
The clutch fluid on mine turned black on the 10...

The clutch fluid on mine turned black on the 10 mile ride home after the 12k service.
Forum: 998 / 996 / 916 / 748 11-Jul-2003, 23:31
Replies: 4
Views: 2,506
Posted By Nigel Booker
Seems a bit dear to me £149.67+£64.00+VAT =...

Seems a bit dear to me £149.67+£64.00+VAT = £251.06

I paid £125.00 for the C&S and got it fitted by a local non franchised dealer for £35.00. I always hang around the workshop and watch the work...
Forum: 998 / 996 / 916 / 748 11-Jul-2003, 00:32
Replies: 9
Views: 3,936
Posted By Nigel Booker
I bought a 2000 model and was told by the dealer...

I bought a 2000 model and was told by the dealer that was the first of the 996 models with the 5 spoke marchesini wheels and grey frame. I think the 1999 model 996 still came with 3 spoke brembo...
Forum: 998 / 996 / 916 / 748 11-Jul-2003, 00:00
Replies: 6
Views: 2,995
Posted By Nigel Booker
I think you'll find that ducati accept that...

I think you'll find that ducati accept that the likes of sigma and JHP are as if not more qualified to work on ducati engines. That said it may be worth the price of a phone call to ducati uk to...
Showing results 51 to 100 of 115
Page 2 of 3 < 1 2 3 >

 
Recent Posts - Contact Us - DSC Home - Archive - Top
Powered by vBulletin 3.5.4 - Copyright © 2000 - 2026, Jelsoft Enterprises Ltd. - © Ducati Sporting Club UK - All times are GMT +1. The time now is 15:55.