Advice on some parts Im after please - Page 2

rcgbob44 · 14-Feb-2004, 15:22

Jasper
Does Nelly do the correct size (46mm) rear wheel nut either in S/S or Ti?

Rushjob · 14-Feb-2004, 15:29

Stainless, bi-hexagonal, very Gucci!!!!!
Won't fit my ST4S tho......

Jasper · 14-Feb-2004, 19:25

Yes,stainless steel.Two rear and one front in bi-hex.Lovely pieces of kit and don't mark up/corrode like ally ones.

Billythekid · 13-Mar-2004, 00:29

Can anyone please tell me where on earth I can buy the sockets I need to remove the rear wheel and the sprocket carrier?
Largest ive found anywhere so far is only a 32mm!
Am I right in saying i need a 41mm and a 46mm?

Cheers Joel

skidlids · 13-Mar-2004, 00:42

Could try here
http://www.primetools.co.uk/pages/displaycat.asp?271

These are 3/4" drive so you will probably need a 1/2" to 3/4" adapter

Henners · 13-Mar-2004, 08:39

Billy - try Harry (HTB) for your sockets, he has some sets made up and may have some left. Top quality.

Rob B · 13-Mar-2004, 09:16

Or Halfords or your local Discount Motor Spares shop. There are a couple of inch sockets that do the job at low prices.

Rgds,

Rob

rockhopper · 13-Mar-2004, 09:19

If you get them from a tool shop you might need to get the shoulder turned off them so they sit right onto the nut.

rcgbob44 · 13-Mar-2004, 17:46

Billy

Try to find a very cheap tool shop/store.
I got my sockets from a trade show stand, the type that sells all sorts of tools chaep, there with 3/4 drive and cost me £5 each and a 1/2 to 3/4 adaptor cost me £4. I had the Chaps at work skim the sockets so that they fittes straight on the socket, ie removed the bevel from inside the socket.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode
Postbit Selector
		Use Vertical Postbit

14-Feb-2004, 15:22	#11
rcgbob44 DSC Club Member BSB Star Bikes: 2009 Ducati Monster 1100s, KTM 890R Posts: 5,991 Join Date: May 2003 Location: Coulsdon, Surrey...........and hopefully Germany at some point in the future. Mood: I love the Monster and the KTM & I have my wife exactly where she wants me! Jasper Does Nelly do the correct size (46mm) rear wheel nut either in S/S or Ti? Reply

14-Feb-2004, 15:29	#12
Rushjob Registered Forum User Big Twin Posts: 1,802 Join Date: Apr 2002 Location: Lincs Mood: :-) Stainless, bi-hexagonal, very Gucci!!!!! Won't fit my ST4S tho...... Reply

14-Feb-2004, 19:25	#13
Jasper Registered Forum User Ducati Corse Posts: 3,707 Join Date: Jun 2002 Location: YORK Yes,stainless steel.Two rear and one front in bi-hex.Lovely pieces of kit and don't mark up/corrode like ally ones. Reply

13-Mar-2004, 00:29	#14
Billythekid Registered Forum User Montjuic Posts: 51 Join Date: Nov 2003 Location: SouthWest Mood: indifferent Can anyone please tell me where on earth I can buy the sockets I need to remove the rear wheel and the sprocket carrier? Largest ive found anywhere so far is only a 32mm! Am I right in saying i need a 41mm and a 46mm? Cheers Joel Reply

13-Mar-2004, 00:42	#15
skidlids MotoGP God Posts: 18,275 Join Date: Apr 2002 Location: Oxford Mood: Its ONLY a Bike Club Could try here http://www.primetools.co.uk/pages/displaycat.asp?271 These are 3/4" drive so you will probably need a 1/2" to 3/4" adapter Reply

13-Mar-2004, 08:39	#16
Henners Registered Forum User Ducati Corse Posts: 3,338 Join Date: May 2002 Billy - try Harry (HTB) for your sockets, he has some sets made up and may have some left. Top quality. Reply

13-Mar-2004, 09:16	#17
Rob B Registered Forum User Ducati Meccanica Posts: 2,263 Join Date: Aug 2003 Location: Wimbourne, Dorset Mood: I'm so happyyyyyyyyyyyy Or Halfords or your local Discount Motor Spares shop. There are a couple of inch sockets that do the job at low prices. Rgds, Rob Reply

13-Mar-2004, 09:19	#18
rockhopper Registered Forum User Ducati Corse Posts: 3,367 Join Date: Jul 2001 Location: Pinxton If you get them from a tool shop you might need to get the shoulder turned off them so they sit right onto the nut. Reply