749R slipper clutch pressure plate measurement required ? - Page 3

Sharpy G · 02-Aug-2006, 13:16

Quote:

Originally Posted by doogalman

Bit of a misrepresentation with the number plate . Should be fitted to a 999 not a 749. WSS would have been the one!!!!!

erm....it does say SBK on the tank
and its in Ducatis SBK section aint it ?!

toys out of pram .!....................it is a Superbike ! yes it is !!

Sharpy G · 02-Aug-2006, 13:16

BY THE WAY.......for anyone reading this, I do still need the measurement at the beginning of this rambling post

LOL

doogalman · 02-Aug-2006, 14:12

Steady tiger!!!

Sharpy G · 02-Aug-2006, 14:33

Quote:

Originally Posted by doogalman

Steady tiger!!!

Only kidding mate, just made me laugh that I got all these relpies but no dimension

G

Gizmo · 02-Aug-2006, 14:52

Quote:

Originally Posted by Sharpy G

Only kidding mate, just made me laugh that I got all these relpies but no dimension

G

DPP slipper plate is 115mm internal diameter i'd think the 749R would need to be the same as the basket will be same tooth outside diameter.

Sharpy G · 02-Aug-2006, 15:02

Gizmo
thanks, it is 115mm dia inside of teeth, but I need to know what the diam is on the 749R one without the teeth so I can machine them off
cheers

andyb · 02-Aug-2006, 15:05

Buy a proper bloody cover.....or better still a proper clutch!!!!

oh yeah were back to that again.

Sharpy G · 02-Aug-2006, 15:16

DP don't do a pressure plate for the 749R
so this is the only option

"AndyB - you n your 'proper clutches' LOL
like my modded one at the mo
seems to work well with my new Corsa IIIs"

what was it you were saying about roundabouts ?

Gizmo · 02-Aug-2006, 15:29

Quote:

Originally Posted by Sharpy G

Gizmo
thanks, it is 115mm dia inside of teeth, but I need to know what the diam is on the 749R one without the teeth so I can machine them off
cheers

the 749R should be the same, the teeth are on the basket and the basket is the same between bikes cos the clutch plates fit between bikes. So, if the DPP slipper has clearance from the basket teeth the same machined out diameter will work on any slipper pressure plate as it has to clear the same teeth, if you get my drift....

if that ain't enough try measuring across the teeth on your final steel plate, and leave a little clearance, if its close to 115 I'd probably go with that

andyb · 02-Aug-2006, 15:33

If you bought a proper clutch........you could measure that...........

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode
Postbit Selector
		Use Vertical Postbit

02-Aug-2006, 13:16	#22
Sharpy G Registered Forum User Ducati Corse Bikes: 749R 2004 Posts: 3,459 Join Date: Dec 2005 Location: Redhill, Surrey Mood: luvin' bein back out on the 'R' BY THE WAY.......for anyone reading this, I do still need the measurement at the beginning of this rambling post LOL Reply

02-Aug-2006, 14:12	#23
doogalman Registered Forum User WSB Hero Posts: 9,937 Join Date: May 2003 Location: Enjoy as much time without work Mood: No point in working long hours to die early Steady tiger!!! Reply

02-Aug-2006, 15:02	#26
Sharpy G Registered Forum User Ducati Corse Bikes: 749R 2004 Posts: 3,459 Join Date: Dec 2005 Location: Redhill, Surrey Mood: luvin' bein back out on the 'R' Gizmo thanks, it is 115mm dia inside of teeth, but I need to know what the diam is on the 749R one without the teeth so I can machine them off cheers Reply

02-Aug-2006, 15:05	#27
andyb Registered Forum User BSB Star Posts: 6,720 Join Date: Feb 2002 Location: northampton Mood: Has change happened...must of missed it! Buy a proper bloody cover.....or better still a proper clutch!!!! oh yeah were back to that again. Reply

02-Aug-2006, 15:33	#30
andyb Registered Forum User BSB Star Posts: 6,720 Join Date: Feb 2002 Location: northampton Mood: Has change happened...must of missed it! If you bought a proper clutch........you could measure that........... Reply