breaker bars

loverobot · 13-Jan-2006, 10:09

who does everyone use for tools?

I need a 3/4" square drive loooooong breaker bar for the rear wheel nuts

any suggestions / links / recommendations as to makes etc are appreciated

already have the sockets

Scotty Monster · 13-Jan-2006, 11:32

helfrauds £20 ish ~:?

rockhopper · 13-Jan-2006, 13:58

Got a 36 incher for the bike and also a 24 incher that lives in the car boot for undoing wheel nuts both from Halfrauds.

m1keyp · 13-Jan-2006, 14:38

Scaffold pole!!!

BDG · 13-Jan-2006, 14:41

Quote:

Originally posted by Scotty Monster
helfrauds £20 ish ~:?

ditto

24 inch jobbie

loverobot · 13-Jan-2006, 15:31

Cheers
assumed they would have 1/2" only but will go have a look
Thanks

chris.p · 13-Jan-2006, 19:22

A piece of scaffold tube or as in my case a length washing line post, works a treat.

Chris.

bradders · 14-Jan-2006, 00:20

one of those impact driver gun thingies that run off the battery - about £20 and does the job easy with 1 person!

rockhopper · 14-Jan-2006, 00:31

Have they got enough umph to undo a clutch nut?

loverobot · 14-Jan-2006, 00:37

may look at one of those
long 3/4" drive bars seem thin on the ground - seen some on the web but not buy over the counter in / around leeds area

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode
Postbit Selector
Use Horizontal Postbit

13-Jan-2006, 10:09	#1
loverobot Registered Forum User 500SD Posts: 723 Join Date: Aug 2005 Location: leeds breaker bars who does everyone use for tools? I need a 3/4" square drive loooooong breaker bar for the rear wheel nuts any suggestions / links / recommendations as to makes etc are appreciated already have the sockets Reply

13-Jan-2006, 11:32	#2
Scotty Monster Registered Forum User Mille Posts: 185 Join Date: Mar 2005 Location: Gateshead Mood: counting helfrauds £20 ish ~:? Reply

13-Jan-2006, 13:58	#3
rockhopper Registered Forum User Ducati Corse Posts: 3,367 Join Date: Jul 2001 Location: Pinxton Got a 36 incher for the bike and also a 24 incher that lives in the car boot for undoing wheel nuts both from Halfrauds. Reply

13-Jan-2006, 14:38	#4
m1keyp Registered Forum User 500SD Posts: 714 Join Date: Mar 2004 Location: Cambridgeshire Scaffold pole!!! Reply

13-Jan-2006, 15:31	#6
loverobot Registered Forum User 500SD Posts: 723 Join Date: Aug 2005 Location: leeds Cheers assumed they would have 1/2" only but will go have a look Thanks Reply

13-Jan-2006, 19:22	#7
chris.p Registered Forum User Ducati Corse Bikes: Monster 1100 EVO Posts: 3,969 Join Date: Jul 2003 Location: lincoln Mood: I'm A Grandad again :-) A piece of scaffold tube or as in my case a length washing line post, works a treat. Chris. Reply

14-Jan-2006, 00:20	#8
bradders Registered Forum User MotoGP God Bikes: 848, M620 DD bike Posts: 11,913 Join Date: Aug 2003 Location: Hants Mood: waiting... one of those impact driver gun thingies that run off the battery - about £20 and does the job easy with 1 person! Reply

14-Jan-2006, 00:31	#9
rockhopper Registered Forum User Ducati Corse Posts: 3,367 Join Date: Jul 2001 Location: Pinxton Have they got enough umph to undo a clutch nut? Reply

14-Jan-2006, 00:37	#10
loverobot Registered Forum User 500SD Posts: 723 Join Date: Aug 2005 Location: leeds may look at one of those long 3/4" drive bars seem thin on the ground - seen some on the web but not buy over the counter in / around leeds area Reply