Rear Hub removal

martins · 28-Aug-2004, 19:22

Prior to fitting a quick change carrier-(Neil Stedman has offered to post me details of how to fit the carrier-appreciated) I went into the garage to remove the rear hub for polishing, but the retaining bolts keep going around, how do you stop them from rotating in order to remove the nuts to get the Hub off?

Help appreciated

desmojen · 28-Aug-2004, 19:28

You take the big nut off at the front and then take off the sprocket/carrier as a oner. Then you will see a large allen key in the back of each cush drive to hold while you undo the nut.

martins · 28-Aug-2004, 19:35

Sorry to be thick, do I need to remove the chain?

desmojen · 28-Aug-2004, 20:15

Lol, don't worry, I'm no einstein either!
The chain will come off when you take out the sprocket, you don't have to take it right off the bike though.

Mr_S · 28-Aug-2004, 20:55

Have a look at the file here, it's the one I used and it's well written.

I'd recommend reading it through first though, as the allen key needed to remove the cush rubbers isn't mentioned in the tool list (12mm IIRC)

http://www.ducati.ms/ubbthreads/down...ch_id=177?Cat=

Jason

martins · 28-Aug-2004, 22:02

Thanks guys, I appreciate all of your help.

I have never been one to do my own bike work, but as I am now over 40 I thought it is about time I had a go, a bit scarry but I am determined to fit my own quick change carrier.

all I need to ask you now the the size of the large Hub nut?, so I can pop around to borry from my mates Snap on Tool box!, I have the 46mm for the wheel I even have a torque wench!-all of my own!

Mr_S · 28-Aug-2004, 23:36

41mm then is what you'll be needing. If you can borrow one with the shoulders machined down you're less likely to slip off the nut as it's quite shallow.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode
Postbit Selector
Use Horizontal Postbit

28-Aug-2004, 19:28	#2
desmojen Registered Forum User 500SD Posts: 546 Join Date: Aug 2004 Location: Lyneham, Wilts Mood: DOH! You take the big nut off at the front and then take off the sprocket/carrier as a oner. Then you will see a large allen key in the back of each cush drive to hold while you undo the nut. Reply

28-Aug-2004, 19:35	#3
martins Registered Forum User Mille Bikes: 2013 Monster 796 2012 Harley Davidson Softail Slim Posts: 218 Join Date: Jun 2001 Location: Northants Rear hub removal Sorry to be thick, do I need to remove the chain? Reply

28-Aug-2004, 20:15	#4
desmojen Registered Forum User 500SD Posts: 546 Join Date: Aug 2004 Location: Lyneham, Wilts Mood: DOH! Lol, don't worry, I'm no einstein either! The chain will come off when you take out the sprocket, you don't have to take it right off the bike though. Reply

28-Aug-2004, 20:55	#5
Mr_S Registered Forum User Big Twin Posts: 1,324 Join Date: Mar 2004 Location: Gosport Have a look at the file here, it's the one I used and it's well written. I'd recommend reading it through first though, as the allen key needed to remove the cush rubbers isn't mentioned in the tool list (12mm IIRC) http://www.ducati.ms/ubbthreads/down...ch_id=177?Cat= Jason Reply

28-Aug-2004, 23:36	#7
Mr_S Registered Forum User Big Twin Posts: 1,324 Join Date: Mar 2004 Location: Gosport 41mm then is what you'll be needing. If you can borrow one with the shoulders machined down you're less likely to slip off the nut as it's quite shallow. Reply